It can be installed on plastic and steel tanks, however, if the tank contains any ribs, stays or bars for stability then they could cause interference with the ultrasonic signal. Please contact us if you have any questions about the suitability of the device on your tank: https://dunravensystems. A tank mounted ultrasonic transmitter unit, compatible with the standard 32mm port fitted to modern plastic oil storage tanks.

I have lost the instructions – how do I rematch the unit and how do I know what Pin settings to set on the rear of the receiver plug. Thanks to their hydrophobic nature, these oil spill absorbent pads will not soak up water and will float on top even when completely saturated, which makes them suitable for applications where oil and water must be separated. The transmitter uses ultrasonic technology, which means that the transmitter sends a signal out towards the oil surface and it bounces back to the device. In this case, remove the transmitter from the tank, check for the correct dipswitch settings on the back of the receiver, which corresponds to your tank height and rematch by following the installation instructions.This heating oil tank gauge uses an ultrasonic level sensor located at the top of the tank which sends out the sound waves in the form of bursts in a downward direction to the fluid in the tank. Whilst used within many industries for filtering water out of the fuel in a diesel storage tank, thanks to being suitable for gravy fed installations as well as compatible pumping systems, GoldenRod fuel filters are widely recognised amongst the farming community. Ideal for monitoring heating oil and diesel but suitable too for a wide range of liquids including admixtures, agricultural fuel oil, anti-freeze, biodiesel, bio heating oil, fuel oil, detergents, lubricants, waste oil and water. Try and relocate the receiver to a position that is nearer a window, remember that the transmitter communicates with the receiver by use of an FM signal and moving the receiver plug from possible metal obstructions can improve the signal. We'll be happy to send you a copy, so you can easily browse through our wide range of products wherever you are.

Every Apollo Ultrasonic Tank Level Monitor is supplied complete with long life lithium battery, full instructions and immediate fittings as standard. On installation, the float switch/sensor must be located between the inner tank and the internal wall of the bund. bars tells you that the tank is full and when the level reaches a low preset level in the tank an “Early Warning Nozzle” is shown. This information is displayed on the transmitter’s integral LCD display and also relayed wirelessly to the receiver unit. Apollo is the revolutionary way to take control of your fuel and allows you to monitor the level of fuel inside your oil tank, from the warmth and comfort of your home or office.The transmitter monitors the level of fuel inside the tank and relays this data via a secure, wireless connection to the receiver unit, which cleverly and conveniently plugs into a standard electrical socket. These oil spill pads are more durable than the Eco versions; even when used excessively and fully saturated they will not lint and pulp, and their tougher low-linting exterior enables them to be stood on and used as a wipe.

In cases where full readings persist, remove the transmitter from the tank and go through a re-matching procedure, and test before refitting to the tank. The lithium (CR2430 supplied) battery operated transmitter fits plastic or steel tanks up to 3 metres high and transmits up to 200 m to the receiver, which will auto-reset after a power failure. This would allow an engineer to replace the filter without draining the contents of the tank should the filter ever need changing. My oil tank just has a 20mm hole on the top so, having spoken to a very helpful guy in Ray Grahams, the Apollo was the only one that was suitable for my particular tank (unless I wanted to start drilling a bigger hole, which I didn't!The Apollo Visual Oil Level Monitor, builds upon the success of the original Apollo Tank Contents Gauge, but usefully incorporates local as well as remote reading functionality, via the transmitter unit’s inbuilt LCD display. The K150 mechanical flow meter meets the ATEX/IECEx requirements for the use of materials in potentially explosive atmospheres. The Cim-Tek Tank Dryer is a fuel tank water absorber, which has been developed in response to the increasing concerns regarding water contamination of fuel. What if the oil in the tank is full to the very top, will this harm the Apollo transmitter and will I receive a correct reading? Use of longer screws and/or if they are put in at an angle will interfere with readings and as a result, may show a full reading.

Certainly, the Apollo can be used on multiple piped tanks to measure the level provided the tanks are the same shape and capacity with open pipework linking the tanks.Remember to switch the power off and then back on before rematching to allow for receiver plug to go into teach mode.